Renin Barn Door Hardware - Easy Latch Installation Instructions
Easy Latch Installation Instructions
TM
PLEASE READ CAREFULLY IMPORTANT! • Read all instructions carefully. • Protect your eyes by wearing safety goggles. • Keep the installation area free of clutter. • Follow each step completely before starting the next step.
VERIFY THAT ALL PARTS ARE INCLUDED IN THE PACKAGING. IF ANY PARTS ARE MISSING, DO NOT RETURN THIS PRODUCT TO THE STORE. FOR PARTS ASSISTANCE, PLEASE CALL 1-800-493-5263 BETWEEN 8:30 AM AND 4:30 PM EST, MONDAY TO FRIDAY. SUPPORT IS PROVIDED IN ENGLISH, FRENCH AND SPANISH.
PACKAGE CONTENTS
7
12
Customizable labels in English, French and Spanish
5
Latch
Set Screws on back of Catch Block
8
9
1
2
Handle
10
11
Large Screws
Small Screws
3
4
6
1x | Handle Assembly Cover
5 2x | T Brackets
9 1x | Catch Block Allen Key
1
2 1x | Easy Latch Handle Assembly
6 4x | T Bracket Screws
10 1x | Left Door End Stop
1x | Engagement Pin Block Assembly
3 1x | Emergency Key
11 1x | Right Door End Stop
7
4 4x | Handle Assembly Screws
8 1x | Catch Block
12 1x | Square Rod
TOOLS REQUIRED (NOT PROVIDED)
Measuring Tape
Pencil
Awl or Nail
Cordless Drill
1/8� Drill Bit
Phillips Screwdriver
2 | Installation Instructions
REN I N . COM
1
Make Measurements.
Measure down 47 ½" from the bottom of the track and make a small line on the edge of the door near where the handle will be installed. Note 1: Please ensure your door is fully installed and remains on the track before installing Renin's Easy Latch. Note 2: Latch Handle Assembly is located on the inside of room requiring privacy
2
A) Position the bottom edge of one (1) T bracket on the line, centered on the edge of the door and mark a hole location in the center of each slot. B) Position the top edge of the door handle assembly at the line made in Step 1, ensuring the small lip is located on the edge of the door and mark the 4 hole locations with an awl. Note: A nail will also suffice. C) Position the top edge of one (1) T bracket 5/8" from the top of the door edge, centered on the door side and mark a hole location in the center of each slot.
B
A
C
Small Lip
3
A) Using a 1/8" drill bit, drill all the marked hole locations ¾" deep, including the front door assembly holes. Note: Do not drill deeper then ¾" and/or do not drill through the door.
| 3 Installation Instructions
TM
4
Attach Both T Brackets
A) Affix both T brackets ( 1 upper and 2 lower) using the 1" screws provided. Note: Ensure the brackets are centered on the door.
1
2
Front of Door
6
5 A) Insert the square
Square rod through T bracket
A
A) Insert the
8 engagement pin block assembly into the bottom end of the rod, with the pin facing the side of the door the handle will be affixed to (as shown in step 8). Note: Angle the rod slightly so you can access the screw holes and affix with the screws provided. A) Position the handle assembly on the door, ensuring the handle is in the lowered position (as shown) and the engagement pin is located in the slot of the handle. B) Affix the handle assembly to the predrilled holes in the door using the screws provided.
rod down through the lower T bracket on a slight angle. are at the bottom of the square rod, are facing the door side edge.
Front of Door
B) Ensure the holes
Front of Door
Edge
B
7
A) Raise the rod up
Front of Door
through the upper T bracket.
Note: Rod should touch the track.
Handle is in lowered position
4 | Installation Instructions
REN I N . COM
9
Replace End Stops
A) Remove the existing door stops from each end of the track. B) Replace with the End Stops provided. C) Position End Stops so the door is in the desired open and closed position and tighten the set screws with Allen Key. Note: The New End Stops should work on most standard 78 3/4˝ and 96˝ track.
A
B
C
10
Set the Catch Block
A) Have a second person stay on the handle side of the door (Front) while you move the door to the closed position. B) Hold the Catch Block onto the bottom of the track Note: Place outside of the new end stop with the Catch Block set screws facing toward the back. C) Have the other person push the handle in and rotate it downward to raise the rod into the catch block. D) Tighten the set screws. Note: Ensure the handle seats in the locked position, and has to be pushed inward to actuate the rod up or down.
11
12
A
A) Snap the cover onto the handle assembly ensuring the emergency key slots face the side of the rod.
A) Test the
emergency key so you are familiar with how it operates. B) Store the key at the back of the track, between the track and the catch block as shown.
B
Emergency Key Slots
| 5 Installation Instructions
TM
You did it! Enjoy your new Renin Easy Latch
5 YEAR LIMITED WARRANTY Renin warranties their products against manufacturing defects for up to three years from the purchase date. The warranty applies only to the original purchaser of the product from Renin. If a product is determined to be defective due to a manufacturing defect, Renin will supply a replacement product.
The scope of the warranty is limited to replacing the product and does not include labor required to install, repair or deliver, or any costs related to removing the existing product. This warranty is void in the event that the product is damaged in transit, or if damage or failure is caused by abuse, misuse, storage of products in an improper environment, abnormal usage, faulty installation, failure to follow installation instructions, damage in an accident, improper maintenance, or any repair. Renin reserves the right to inspect any claim prior to issuing credit. Once again, congratulations on your new Renin Product! To learn more about our complete line of products or if you have any questions, call 1-800-493-5263 between 8:30am and 4:30pm, Monday to Friday. We can also be reached online: info@renincorp.com.
Follow Us
T. (800) 493-5263 F. (905) 791-7930
W. RENIN.COM E. INFO@RENIN.COM
1141 RYDER STREET TUPELO, MS 38804
110 WALKER DRIVE BRAMPTON, ON L6T 4H6
6 | Installation Instructions
Page 1 Page 2 Page 3 Page 4 Page 5 Page 6Powered by FlippingBook