Inswing Patio Doors Elevation Charts
Inswing Patio Doors | French Doors
Inswing Patio Door – French Door
5'-1 11/16" 4'-11 15/16" 20 5/16"
5'-1 11/16" 4'-11 15/16" 20 5/16"
6'-1 11/16" 5'-11 15/16" 26 5/16"
6'-1 11/16" 5'-11 15/16" 26 5/16"
U.D.
R.O.
G.S.
ACT
ACT
ACT INACT
INACT
ACT
INACT
INACT
41166AL
41166AR
51166AL
51166AR
ACT
ACT
ACT INACT
INACT
ACT
INACT
INACT
51180AL
51180AR
41180AR
41180AL
Operation is viewed from the interior.
Rectangular Transoms Inswing Patio Doors | Rectangular Transoms
Dimension Calculations
2'-8 1/2" 2'-6 1/2" 24 1/2"
5'-1 11/16" 4'-11 11/16" 53 11/16"
3'-2 1/2" 3'-0 1/2" 30 1/2"
6'-1 11/16" 5'-11 11/16" 65 11/16"
U.D.
R.O.
G.S.
Elevation charts provide wood unit dimensions for units with the standard 1-15/16" brickmould. Below are the calculations to determine the frame size of units with brickmould.
2610
3010
41110
51110
Width Height
1-15/16" brickmould; U.D. to F.S.
-2 1/4"
-1 1/8"
2614
3014
41114
51114
3-1/2" flat or profiled casing; U.D. to F.S. -5 3/8" 3-1/2" casing and backband; U.D. to F.S. -6 7/8"
-2 11/16" -3 7/16"
2616
3016
41116
51116
F.S. to Panel O.S.M. (1-wide, active)
-1 13/16" -2 23/32"
(1-wide, stationary)
-1 3/4"
-2 23/32"
2618
3018
41118
51118
(2-wide) (3-wide)
-2 9/16"÷2 -2 23/32" -3 5/16"÷3 -2 23/32"
Panel O.S.M. to G.S.
-8 1/8"
-11 3/32"
51120
2620
3020
41120
G.S. to D.L.O.
-1" -1" Note : Clear opening dimensions can be found on pg. 200.
51126
2626
3026
41126
F.S. = Frame Size • G.S. = Glass Size • O.S.M. = Outside Measurement D.L.O. = Daylight Opening • U.D. = Unit Dimension
U.D. = Unit Dimension • R.O. = Rough Opening • G.S. = Glass Size
NOTE: All measurements are nominal. Elevation charts are not to scale. Rectangular transom units are sash set as standard. The units shown are stand-alone units. Adjustments may be required when stacking over other units; adjustments will be made in the factory. Divided lite configurations must be specified when ordering. Specify inswing when ordering. Some installation procedures will require a larger rough opening than noted (i.e. installations utilizing our installation clips), therefore, you may need to increase the rough opening size accordingly. Rough opening gaps may be increased up to a maximum of 1/2" on all sides and still be within good practice guidelines. For rough opening recommendations, see pg. 194. Additional and the most current drawings are available at www.kolbewindows.com .
Kolbe Windows & Doors 162
Powered by FlippingBook